Marolex NEXT 3000 | Battery Sprayer for PPF Slip Solution
  • New
€69.90
Royal Pads Open Flow Polishing Box 130mm
  • New
€43.90
Royal Liquid Pad Cleaner
  • New
€10.90
Royal Liquid Final Touch
  • New
€11.90
Koch Chemie Quick Finish
  • New
€20.90
  • New
    Marolex Sprayer NEXT 3000
    Marolex Sprayer NEXT 3000

    Marolex Sprayer NEXT 3000

    Reviews (0)
    €69.90
    Tax included

    Press the button and spray, no pumping. For PPF slip solution and mild interior cleaners, with a battery good for about 2 hours of work.

    Quantity :
    Write your review

    EU3234363840424446USXX5XSSMLXLXXLXXLArm Length6161,56262,56363,56464,5Bust Circumference8084889296101106111Waist Girth6165697377828792Hip Circumference87919599103108113118

    • Security policySecurity policy(edit with the Customer Reassurance module)
    • Delivery policyDelivery policy(edit with the Customer Reassurance module)
    • Return policyReturn policy(edit with the Customer Reassurance module)

    When installing paint protection film, an evenly wet surface is what matters: the film has to slide until you set it in exactly the right place. With a manual sprayer that means constant pumping, and the spray gets weaker towards the end of every panel.

    Marolex NEXT 3000 is a battery-powered sprayer with a 3-litre tank, where the pressure comes from a diaphragm pump in the head rather than from your hand. Press the button and it sprays slip solution evenly onto the paint or the adhesive side of the film at a constant 3 bar. It works just as well for interior detailing with a mild, diluted cleaner for plastics, vinyl and door cards. The lithium-ion battery charges via USB and, according to the manufacturer, lasts for about 2 hours of work. Marolex has been developing and manufacturing sprayers since 1987, and NEXT is its lightest battery model: just 0.58 kg empty.

    At a glance

    At a glance
    What it is Battery-powered hand sprayer, 3 l
    For PPF slip solution, mild diluted interior cleaners, water
    For whom PPF installers, detailing studios, demanding enthusiasts
    Power Built-in lithium-ion battery, micro USB charging

    Why choose Marolex NEXT 3000?

    • No pumping: the diaphragm pump holds a constant 3 bar from the first panel to the last, so the spray is the same at the start and the end of an install.
    • Controlled flow: 0.35 to 0.55 litres per minute with the original nozzle. The surface stays wet enough for the film to slide, without solution running down doors and sills.
    • Three nozzles included: adjustable MR 1.5 (from mist to jet), round MR 1.0 for fine misting and flat-fan MF 1.5-80° for quickly wetting large panels such as the bonnet or roof.
    • Light and ergonomic: 0.58 kg empty, with a 30 cm lance that reaches inner edges and door handle recesses without tilting the sprayer.
    • Charge indicator: press the button to see the battery level in percent, so a flat battery never catches you mid-install. After 7 minutes of continuous running the pump switches off for safety; press the button to start again.

    Technical specifications

    Technical specifications
    Manufacturer Marolex
    Product type Battery-powered hand sprayer
    Working capacity 3.0 l
    Working pressure 0.3 MPa (3 bar)
    Flow rate 0.35–0.55 l/min (MR 1.0 / MR 1.5)
    Pump Diaphragm, continuous operation
    Battery Lithium-ion, built into the head; charging DC 4 V / 0.8 A via micro USB, 2–4 hours
    Weight (empty) 0.58 kg
    Tank material Polyethylene
    Suitable for PPF slip solutions, mild diluted interior cleaners (neutral or mild pH), clean water
    Not suitable for acidic and alkaline cleaners (wheel cleaners, TFR, iron remover), alcohol and IPA tack solutions, solvents, disinfectants, viscous liquids, liquids above 40 °C

    What to combine it with?

    What to combine it with
    Step Purpose Product
    1 Squeegees and tools for PPF installation PPF and wrap accessories
    2 Mild cleaner for interior plastics and trim Interior cleaners
    3 Brush for gaps, vents and seams Brushes
    4 Wiping and drying after cleaning Interior microfibres

    Tips for the best result

    For PPF installation: make your slip solution with distilled or demineralised water and a few drops of mild shampoo or a dedicated slip concentrate. Soft water leaves no limescale under the film and does not clog the nozzle. Keep a separate hand sprayer for IPA tack solution, as alcohol is not intended for this model.

    For interior cleaning: dilute the cleaner according to its manufacturer and mist it onto a microfibre cloth or directly onto the plastic, never onto screens or electronics.

    After every use: rinse the tank several times with clean water and let the pump run for a few seconds so the water also flushes the hose and nozzle. Otherwise shampoo or cleaner residue dries inside the nozzle.

    Frequently asked questions

    Can I fill it with IPA tack solution?

    No. According to the manufacturer, alcohol and solvents are not permitted because they can damage the seals and pump. Use a separate sprayer for tack solution.

    Is it suitable for wheel cleaners or pre-wash products?

    No. Acidic and strongly alkaline cleaners and iron removers are not suitable for this model. For that kind of chemistry, use the Marolex Industry Acid and Industry Alka lines with chemically resistant seals.

    How long does charging take?

    2 to 4 hours, depending on the charger. The manufacturer recommends a standard 1000 mA USB charger. The IN indicator flashes while charging.

    Can I turn the sprayer over to reach low edges?

    Tilting it slightly is fine, but never turn it upside down while it contains liquid, as the electronics are in the head. Use the 30 cm lance for lower edges and sills.

    Marolex NEXT 3000 saves you the pumping and gives you an evenly wet surface on every PPF install and interior job: press and spray. Marolex manufactures manual and battery-powered sprayers for professional and home use. Easy for beginners, effective enough for demanding detailers.

    Marolex
    S161.121
    4 Items

    Specific References

    EAN13
    5904235008105
    MPN
    S161.121

    How to use

    Charging and preparation

    1. Charge the battery before first use — open the rubber cap on the head and connect the micro USB cable to a 1000 mA charger; a battery at 100 % gives you the full working time without interruption.
    2. Unscrew the head and prepare the solution in the tank — for PPF slip, distilled water with a few drops of mild shampoo or slip concentrate; for interiors, cleaner diluted as directed; do not fill above the bulges on the tank, as the pump needs air to hold constant pressure.
    3. Screw the head back on and purge the lance — tilt the sprayer slightly upwards and run it until liquid comes out instead of air; with no air in the hose, the spray stops instantly when you switch off and does not drip.

    Applying PPF slip solution

    1. Wet the panel evenly with the adjustable or flat-fan nozzle — a thin, continuous film of water lets the PPF slide so you can position it exactly.
    2. After removing the release liner, wet the adhesive side of the film too — wet adhesive does not grab too early and does not pick up dust.
    3. While squeegeeing, mist the surface ahead of the squeegee as needed — the squeegee glides smoothly and does not scratch the film.

    Interior cleaning

    1. Set the nozzle to mist and spray onto a microfibre cloth or directly onto the plastic — a mist covers the surface without dripping into gaps and electronics.
    2. Work the surface with a brush or cloth and wipe with a dry microfibre cloth — the diluted cleaner lifts the dirt and the cloth removes it before it dries.

    Maintenance after use

    1. Empty the tank and rinse it several times with clean water, letting the pump spray clean water for a few seconds — this flushes residue out of the hose and nozzle as well.
    2. Clean the nozzle nut under running water and grease its O-ring with silicone grease — other lubricants make the seals swell and damage the sprayer.
    3. Store the sprayer empty, dry and above +4 °C, and top up the battery every 2–3 months — a lithium-ion battery is damaged if left completely flat for long.

    Tip: keep one sprayer for PPF slip and another for interior cleaner. Cleaner residue in slip solution can weaken the film adhesive.

    Important: never turn the sprayer upside down while it contains liquid, as the electronics are in the head. Do not use acidic or alkaline cleaners, alcohol, solvents, disinfectants or liquids above 40 °C.

    Informacije o izdelku

    Reference
    S161.121

    Proizvajalec

    MAROLEX Sp. z o.o., ul. Gdańska 35, 05-152 Łomna, PL
    Phone
    +48 22 751 30 16
    Spletna stran
    https://marolex.pl

    No customer reviews for the moment.

    Write your review
    Marolex Sprayer NEXT 3000
    Marolex NEXT 3000 | Battery Sprayer for PPF Slip Solution
    Marolex Sprayer NEXT 3000
    €69.90
    Tax included